IRQ issues

[hns]

Hi,
I have looked in your traces and found:
Anton:

Code: Select all

Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0047, io.base=0x0000, len=128
hostap_cs: Registered netdevice wifi0
wifi0: Interrupt, but dev not OK
hostap_cs: index 0x01: Vcc 3.3, irq 39, io 0xf6000000-0xf600007f


and
Zsolt:

Code: Select all

Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0047, io.base=0x0000, len=128
hostap_cs: Registered netdevice wifi0
wifi0: Interrupt, but dev not OK
hostap_cs: index 0x01: Vcc 3.3, irq 35, io 0xc4860000-0xc486007f
wifi0: init command completed too quickly - retrying


So I think we should fix this "wifi0: Interrupt, but dev not OK" thing first.

Could you please grep your source code where this message is generated? And probably there is some comment describing what is going on.

What I also see is that the irq number is different.

-- hns

[reddie]

i have IRQ issues too,

when i insert the card dmesg only repeating

wifi0: Interrupt, but dev not OK

the system freezes till i eject the card.

does somebody has an anwser for this ?

[reddie]

this is my dmesg output

Code: Select all

wifi0: Interrupt, but dev not OK
hostap_cs: index 0x01: Vcc 3.3, irq 10, io 0x0200-0x027f
wifi0: prism2_interrupt: ev=0xffff
wifi0: __hfa384x_cmd_no_wait(6) - timeout - reg=0xffff
hostap_cs: first command failed - assuming card does not have primary firmware
wifi0: init command completed too quickly - retrying
wifi0: prism2_interrupt: ev=0xffff
wifi0: __hfa384x_cmd_no_wait(6) - timeout - reg=0xffff
hostap_cs: first command failed - assuming card does not have primary firmware
prism2_hw_init: initialized in 0 ms
wifi0: prism2_interrupt: ev=0xffff
wifi0: prism2_interrupt: ev=0xffff
wifi0: prism2_enable_aux_port - timeout - reg=0xffff
wifi0: prism2_interrupt: ev=0xffff
wifi0: prism2_enable_aux_port - timeout - reg=0xffff
wifi0: valid PDA not found
SWSUPPORT0 write/read failed: FFFF != 8A32
hostap_cs: Initialization failed
prism2_config() failed


why does my system freezes??

[Hoehrer]

Ok, here is a short summary of my experience with my (wrongly)
bought Sandisk ConnectPlus 128MB+Wifi Card.
Info: I'm running 'Wireless'-applet in the OZ-Launcher, so there may be some
messages caused by it.

My entry in the pcmcia config:

Code: Select all

device "hostap_cs"
   class "network" module "hostap", "hostap_cs"

card "SanDisk ConnectPlus WiFi+128Mb"
  manfid 0xd601, 0x0101
  bind "hostap_cs" to 0
  bind "ide-cs" to 1

Memory support doesn't work at all if trying to use the wireless part as well. The memory part alone works perfectly with this entry:

Code: Select all

card "SanDisk ConnectPlus 128Mb"
  manfid 0xd601, 0x0101
  bind "ide-cs" to 1

My System:
OZ 3.5.1
Zaurus: SL-5500d
Linux: 2.4.18-rmk7-pxa3-embedix-021129
Card-Firmware (Stationary?) 1.7.4
Card-H/W: 1.0
hostap_cs: 0.2.4 - 2004-07-17 (Jouni Malinen <jkmaline@cc.hut.fi>)

dmesg output with activated wifi AND memory:

Code: Select all

hostap_crypt: registered algorithm 'NULL'
hostap_cs: 0.2.4 - 2004-07-17 (Jouni Malinen <jkmaline@cc.hut.fi>)
hostap_cs: setting Vcc=33 (constant)
hostap_cs: CS_EVENT_CARD_INSERTION
hostap_cs: ignoring Vcc=33 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0047, io.base=0x0000, len=128
hostap_cs: Registered netdevice wifi0
wifi0: Interrupt, but dev not OK
hostap_cs: index 0x01: Vcc 3.3, irq 35, io 0xc4860000-0xc486007f
wifi0: init command completed too quickly - retrying
prism2_hw_init: initialized in 0 ms
prism2_enable_aux_port: was not disabled!?
prism2_enable_aux_port: was not enabled!?
wifi0: valid PDA not found
wifi0: hfa384x_cmd: entry still in list? (entry=c37437e0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c37437e0, type=0, cmd=0x0021, param0=0xfd0b, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd0b, len=8)
Could not get RID for component NIC
hostap_cs: Initialization failed
prism2_config() failed
ide_attach()
ide_config(0xc37d4780)
hda: SanDisk SDWCFB-128, ATA DISK drive
ide0 at 0xc4860000-0xc4860007,0xc486000e on irq 35
hda: 250880 sectors (128 MB) w/1KiB Cache, CHS=980/8/32
hda:<7>wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=0)wifi0: hfa384x_cmd: command was not completed (res=0, entry=c3743760, type=0, cmd=0x0001, param0=0x0000, EVSTAT=abfe INTEN=2020)
wifi0: interrupt delivery does not seem to work
wifi0: MAC port 0 enabling failed
wifi0: could not enable MAC port
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
hostap_cs: Shutdown failed
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c36c25e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd41, len=34)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc1, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd42, len=6)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c36c25e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd41, len=34)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc1, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd42, len=6)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c36c25e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd41, len=34)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc1, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0xabfe
wifi0: hfa384x_cmd: entry still in list? (entry=c3743760, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd42, len=6)


dmesg output with only wifi (0) activated:

Code: Select all

hostap_crypt: unregistered algorithm 'NULL' (deinit)
hostap_crypt: registered algorithm 'NULL'
hostap_cs: 0.2.4 - 2004-07-17 (Jouni Malinen <jkmaline@cc.hut.fi>)
hostap_cs: setting Vcc=33 (constant)
hostap_cs: CS_EVENT_CARD_INSERTION
hostap_cs: ignoring Vcc=33 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0047, io.base=0x0000, len=128
hostap_cs: Registered netdevice wifi0
wifi0: Interrupt, but dev not OK
hostap_cs: index 0x01: Vcc 3.3, irq 35, io 0xc4860000-0xc486007f
wifi0: init command completed too quickly - retrying
prism2_hw_init: initialized in 0 ms
prism2_enable_aux_port: was not enabled!?
wifi0: valid PDA not found
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0c20, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0c20, type=0, cmd=0x0021, param0=0xfd0b, EVSTAT=0552 INTEN=54bf)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd0b, len=8)
Could not get RID for component NIC
hostap_cs: Initialization failed
prism2_config() failed
wifi0: hfa384x_cmd: entry still in list? (entry=c36c07a0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c07a0, type=0, cmd=0x0001, param0=0x0000, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: MAC port 0 enabling failed
wifi0: could not enable MAC port
wifi0: hfa384x_cmd: entry still in list? (entry=c36c07a0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c07a0, type=0, cmd=0x0002, param0=0x0000, EVSTAT=0552 INTEN=551f)
wifi0: interrupt delivery does not seem to work
hostap_cs: Shutdown failed
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ae0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ae0, type=0, cmd=0x0021, param0=0xfdc6, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ae0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ae0, type=0, cmd=0x0021, param0=0xfdc6, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ae0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ae0, type=0, cmd=0x0021, param0=0xfdc6, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ae0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ae0, type=0, cmd=0x0021, param0=0xfdc6, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ba0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ba0, type=0, cmd=0x0021, param0=0xfd41, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd41, len=34)
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ae0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ae0, type=0, cmd=0x0021, param0=0xfdc1, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc1, len=2)
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ae0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ae0, type=0, cmd=0x0021, param0=0xfd42, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd42, len=6)
wifi0: hfa384x_cmd: entry still in list? (entry=c36c0ba0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c36c0ba0, type=0, cmd=0x0021, param0=0xfd41, EVSTAT=0552 INTEN=1006)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd41, len=34)


Hope that helped anyone.
Is there anything i can do to help ppl get the card to work?
If it is more complicated ( compiling, debugging etc..) a step by step would be cool


Do i need to post this in the hostap-mailing list too (or are most of the hostap hackers reading here too)?
Can i do this without subscribing to it? Jjust curious, i'm not using ML often

Werner

[Hoehrer]

I just wondered about what would happen if i use this configuration:

Code: Select all

card "SanDisk ConnectPlus WiFi+128Mb"
  manfid 0xd601, 0x0101
  bind "hostap_cs" to 1
#  bind "ide-cs" to 1

Mind the 1 instead of the 0 in the hostap_cs line.

Here is the dmesg output:

Code: Select all

hostap_crypt: registered algorithm 'NULL'
hostap_cs: 0.2.4 - 2004-07-17 (Jouni Malinen <jkmaline@cc.hut.fi>)
hostap_cs: setting Vcc=33 (constant)
hostap_cs: CS_EVENT_CARD_INSERTION
hostap_cs: ignoring Vcc=33 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0064, io.base=0x0000, len=16
hostap_cs: Registered netdevice wifi0
hostap_cs: index 0x01: Vcc 3.3, irq 35, io 0xc4860000-0xc486000f
hostap_cs: assuming no Primary image in flash - card initialization not completed
wifi0: test Genesis mode with HCR 0x1f
prism2_pccard_cor_sreset: original COR 45
prism2_pccard_genesis_sreset: original COR 45
Readback test failed, HCR 0x1f write 00 e1 a1 ff read 80 7e 80 7e
wifi0: test Genesis mode with HCR 0x0f
prism2_pccard_cor_sreset: original COR 45
wifi0: Command completion event, but no pending commands
prism2_pccard_genesis_sreset: original COR 45
Readback test failed, HCR 0x0f write 00 e1 a1 ff read 80 7e 80 7e
prism2_pccard_genesis_sreset: original COR 45
wifi0: registered netdevice wlan0
wifi0: could not set interface UP - no PRI f/w
wlan0: could not set interface UP - no PRI f/w
wlan0: could not set interface UP - no PRI f/w
wifi0: cannot get RID fdc6 (len=12) - no PRI f/w
wifi0: cannot get RID fdc6 (len=12) - no PRI f/w
wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
wifi0: cannot get RID fdc6 (len=12) - no PRI f/w
wifi0: cannot get RID fdc6 (len=12) - no PRI f/w
wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
wifi0: cannot get RID fdc6 (len=12) - no PRI f/w
wifi0: cannot get RID fdc6 (len=12) - no PRI f/w
wifi0: cannot get RID fd41 (len=34) - no PRI f/w
wifi0: cannot get RID fdc1 (len=2) - no PRI f/w
wifi0: cannot get RID fd42 (len=6) - no PRI f/w
wifi0: cannot get RID fd41 (len=34) - no PRI f/w
wifi0: cannot get RID fdc1 (len=2) - no PRI f/w
wifi0: cannot get RID fd42 (len=6) - no PRI f/w
wifi0: cannot get RID fd41 (len=34) - no PRI f/w
wifi0: cannot get RID fdc1 (len=2) - no PRI f/w
wifi0: cannot get RID fd42 (len=6) - no PRI f/w
wifi0: cannot get RID fd41 (len=34) - no PRI f/w
wifi0: cannot get RID fdc1 (len=2) - no PRI f/w
wifi0: cannot get RID fd42 (len=6) - no PRI f/w
wifi0: cannot get RID fd41 (len=34) - no PRI f/w
wifi0: cannot get RID fdc1 (len=2) - no PRI f/w
wifi0: cannot get RID fd42 (len=6) - no PRI f/w
wifi0: cannot get RID fd41 (len=34) - no PRI f/w
wifi0: cannot get RID fdc1 (len=2) - no PRI f/w
wifi0: cannot get RID fd42 (len=6) - no PRI f/w
wifi0: cannot get RID fd41 (len=34) - no PRI f/w
wifi0: cannot get RID fdc1 (len=2) - no PRI f/w
wifi0: cannot get RID fd42 (len=6) - no PRI f/w


Doesn't seem to work as well
Why is the wlan device used too here?

Werner

[hns]

Is there anything i can do to help ppl get the card to work?
If it is more complicated ( compiling, debugging etc..) a step by step would be cool

Do i need to post this in the hostap-mailing list too (or are most of the hostap hackers reading here too)?
Can i do this without subscribing to it? Jjust curious, i'm not using ML often

Werner,
1. Submitting reports like these is already a lot of help for the (small) community which is forming in this forum!

2. Anton has recently provided a (short) description how to compile hostap (is stored here in this forum)

3. The hostap-maintainers would appreciate that (just make a copy&paste from this forum) - although I think they focus on very different issues than the connect+ initialization issues.

4. The hostap main hackers are on the hostap list only - this forum has been installed to collect & archive all the special connect+ issues (which have been interspersed into approx. 3000 mails per year) and I assume only those interested in this card come here. But I am doing some cross-posting to keep the information flowing.

5. I think the hostap mailing list is on subscription base only - and you will receive approx. 3000 mails per year = 10 per day! And you have to filter out the one relevant mail every 4 weeks. That was the main reason why I have created this forum - to allow to focus on the connect+ issue here and to have a real archive.

-- hns

[Hoehrer]

Werner,
1. Submitting reports like these is already a lot of help for the (small) community which is forming in this forum!

Thanks for the response, that's good to hear

2. Anton has recently provided a (short) description how to compile hostap (is stored here in this forum)

I've tried to follow them today (making a hostap_cs module, not the kernel-rebuild), but i'm getting problem after problem (i always hated compiling anything that has more than one file )

Code: Select all

make
make -C /usr/src/linux SUBDIRS=/mnt/hdb3/temp/dev/hostap-driver-0.2.5/driver/modules \
        MODVERDIR=/mnt/hdb3/temp/dev/hostap-driver-0.2.5/driver/modules modules
make[1]: Entering directory `/usr/src/kernel-headers-2.6.4-1-k7'
  SPLIT   include/linux/autoconf.h -> include/config/*
make[1]: scripts/split-include: Kommando nicht gefunden
make[1]: *** [include/config/MARKER] Fehler 127
make[1]: Leaving directory `/usr/src/kernel-headers-2.6.4-1-k7'
make: *** [2.6] Fehler 2

make obviously uses the (wrong) 2.6.x kernel sources, but i though it only needs the header files from the 2.4 files?

How do i tell make to do point 3 in the howto (use arm):

3. Select proper configuration based on your Z model (arm/arch/def-configs/sl5500up for 5500 US model)

I used the script dev-arm-qpe.sh (from here to set the environment for arm , but i'm not sure if this is doing anything that helps me.


Thanks again,
Werner